Qian Rui stainless steel water tank Stainless steel water tank factory major products categories are: corrugated stainless steel water tank modular stainless steel tanks, stainless steel liner fiberglass tanks (patent products) spherical stainless steel water tanks, square stainless steel tanks, stainless steel tanks ellipsoid, horizontal stainless steel water tank , vertical stainless steel water tank, a cylindrical stainless steel tank, lined with stainless steel tank fabricated of stainless steel tanks, stainless steel water tank. Product structure design structural points lower water tank and high water tank are two of them lower tank chamber (generally divided into 1 × 1m, 1 × 1.5m, 1 × 2m, 1 × 3m four kinds) inclusive of the steady flow tank mounted on The booster set, cabinet, etc., steady flow tank separately from the municipal pipe network and water tanks, the compact design, especially pay attention to appearance; high water tank inlet and outlet tubes to consider supporting the whole system, the design has more particularity. 1, the inlet pipe placed in the water tank at a higher, generally based on flow calculation diameter, low water tank has municipal pipe network directly to a steady flow of water tank, water tank inlet pipe can be smaller; high water tank if relatively large, you can calculate the daily average flow Otherwise, according to hourly average flow calculation. Provisional DN40 DN50, DN65 third gear, 0.6MPa flange connection. With float valve inlet must. Standard inlet on the water tank on the right. 2, outlet pipe placed in the tank the lowest, diameter is determined by matching flow device, 0.6MPa flange connection. Standard outlet pipe on the tank left. 3, overflow pipe diameter generally larger than the inlet pipe big 1-2, the highest point on the side of the tank, the pipe is positioned higher than the bottom of the float valve in the closed position about 20-30mm. Not valving, there should be dust, insects and other measures overflow pipes, PVC pipe can lead to mergers and vent pipes. Standard overflow pipes on the tank left. 4, vent pipe diameter is generally not less than DN50, pick out from the bottom of the tank, plus pick elbow after loading gate leads from the tank side entry gutter. Standard tank vent pipe on the left. 5, the top of the tank should snorkel diameter generally not less than DN50, should dust, insects and other measures should generally set the nozzle down, the valve can not be installed on the snorkel. It can be considered tops in the air filter snorkel. 6, the top of the tank should be someone manhole arranged in the vicinity of the inlet side, easy maintenance float valve and the like; manhole side should escalator, escalators and manhole ear module climb connection with M10 bolts. Standard manholes, water tanks on the right side of the escalator. 7, the lowest place side tank left R1 / 2 port, followed by the ball valve installed gauge. Specification Specification tank tank module: (1) 1000 × 1000 × 1 (2) 1000 × 1000 × 1.2 (3) 1000 × 1000 × 1.5 (4) 1000 × 1000 × 2 (with less) (5) 1000 × 500 × 1 (6) 1000 × 500 × 1.2 (7) 1000 × 500 × 1.5 (8) 1000 × 500 × 2 (with less) (9) 500 × 500 × 1 (10) 500 × 500 × 1.2 (11) 500 × 500 × 1.5 (12) 500 × 500 × 2 (with less) wherein a thickness of 1mm for the cover, 1.2mm for the upper plate, 1.5mm for the middle of the side plates, 2mm for the lower side board. 2mm backplane with the entire board. Base design considerations should lead to the bottom of the tank vent pipe, the base generally use 14 # channel, middle channel line up with the same one meter square grid. KQF series in the corresponding steady flow tank installation position welding same channel, and pre-drilled mounting holes steady flow tank. To lead the vent pipe on the side of the channel position reserved for φ70 hole for vent pipe (DN50) through. Annex --φ550 tank manhole manholes, made 1000 × 1000 × 1.5 module, there are two escalators in the side to do the climb ear hole φ12. There are lockable mechanism. Escalator - polished stainless steel using 30 × 30 or 36 × 24 square tube polished stainless steel rectangular tube production, width 380mm, height of each section 300mm, leave the box from the 220mm. The upper portion of the human ear hole to climb M10 bolt connection, the lower portion of the housing and cover ground at the contact of rubber or plastic sleeves (such as ready-made products can not be found to cancel). At least at the side of the tank R1 / 2 interface, then 1/2 ball after loading level sensors, sensor accuracy 0.1m, the maximum range of <5m. Internal reinforcement ribs to 40 × 30mm channel, with the stainless steel scrap folded. Gradually flattens the tank module tank during the four corners of each piece welds tank module, should the tank and the tank opposite corner modules to be reliable seam welding, in order to ensure the overall strength of the tank. Ribs are staggered at the intersection, but not bent.